Operation is subject to the following Page 4 The CE mark on the product indicates that the system has been tested to and conforms with the provisions Page 6 Serial Port Connection Page 7 Intercharacter, Interfunction, and Intermessage Delays Page 8 Code Page 10 MicroPDF
|Published (Last):||8 November 2008|
|PDF File Size:||20.23 Mb|
|ePub File Size:||16.98 Mb|
|Price:||Free* [*Free Regsitration Required]|
Operation is subject to the following Page 4 The CE mark on the product indicates that the system has been tested to and conforms with the provisions Page 6 Serial Port Connection Page 7 Intercharacter, Interfunction, and Intermessage Delays Page 8 Code Page 10 MicroPDF Page 11 Menu Commands The IT marks a Page 14 Unpacking the Scanner Open the carton. Page 17 Note: Measurements are in inches.
Page 21 Note: After scanning one of these codes, you must re-boot the cash register. Page 22 Note: After scanning one of these codes, you must re-boot the cash register.
The IT, and Page 31 Keyboard Country Scan the Program Keyboard Country bar code below, then scan the numeric bar code s from the inside back Shift Lock If the Page 34 Serial Port Connection All communication parameters between the scanner and terminal must match for correct data transfer through the serial Page 35 Baud Rate Baud Rate sends the data from the scanner to the terminal at the specified rate.
The host terminal Page 38 RS Handshaking RS handshaking is a set of rules concerning the exchange of data between serially communicating devices. Page 40 Wand Emulation Polarity The Polarity can be sent as standard with black bars high, or reversed with white bars high Data Block Size Page 42 Overall Checksum When this option is turned on, a computed check character is added at the end of the entire Page 43 3 Output Scan Rate Adjusting the scan rate changes the current draw when scanning.
The slower the scan rate, the Page 45 Reread Delay This sets the time period before the scanner can read the same bar code a second time. Page 46 Good Read Delay This sets the minimum amount of time before the scanner can read another bar code. Then the LEDs turn on Page 50 Step 3. Scan the 2 hex digits from the Programming Chart inside the back cover or scan 9, 9 for Certain characters may differ depending on Page 56 Function Code Transmit When this selection is enabled and function codes are contained within the scanned data, the scanner transmits Page 57 Note: If you make an error while scanning the digits before scanning Save , scan Discard on the back cover, scan Page 58 Interfunction Delay This is a delay of up to milliseconds in multiples of 5 placed between the transmission of For example, Page 60 Note: The wildcard for all terminal types is Step 4.
Code I. On page , find the symbology to Page 62 ters to be replaced and xx2 defines replacement characters, continuing through zz1 and zz2. E5 Terminates character replacement. Page 63 Data Formatter When Data Formatter is turned off, the bar code data is output to the host as read including Page 66 Secondary Non Decoded Output Laser Emulation Use this selection when connecting to a secondary terminal with integral decoding.
This also Page 67 Non Decoded Laser Emulation Idle The idle describes the state of the scanner when no data is being transmitted. Page 68 Automatic Trigger: The scanner scans continuously at full power. This programming section Page 70 Message Length Description You are able to set the valid reading length of some of the bar code symbologies.
Page 73 Concatenation Codabar supports symbol concatenation. Page 75 Code 39, continued Check Character No Check Character indicates that the scanner reads and transmits bar code data with or Page 76 Code 39 Append This function allows the scanner to append the data from several Code 39 bar codes together before Refer to Message Length Description Note: The higher the percentage of Page 2. Click on the entry for Visual Menu.
When prompted, select Save File, and save the files to the Prefix to All Symbologies This selection allows you to turn on transmission Page Specular Effect Reduction When the On code is scanned, the first pass read rate and voting threshold are increased. Page 12 Serial Programming Commands The serial programming commands can be used in place of the programming bar codes.
Both the Page Query Commands Several special characters can be used to query the device about its settings. Page When responding, the device echoes back the command sequence with the status character inserted directly before each of the punctuation Page Trigger Commands You can activate and deactivate the scanner with serial trigger commands.
First, the scanner must be put in I25CK20 Interleaved Page Conventional laser data format is provided at the modular connector in the scanner handle. The interface cable is terminated Page Decoded output data format provided at 10 pin RJ41 modular connector in scanner handle.
Wand Emulation 1 2 Cord These services are to be performed Page Replacing the Interface Cable The standard interface cable is attached to the scanner with an pin modular connector. When properly The trigger works. Is the scanner having Page Online Product Service and Repair Assistance You can also access product service and repair assistance online at www. Technical Assistance Page All provisions of this Limited Warranty are separate and severable, which means that if any provision is held invalid and
Hand Held Products IT3800 Manuals
Wand Emulation Polarity The idle describes the state of the scanner when no data is being transmitted. The IT marks a new performance level for handheld scanners. Intercharacter, Interfunction, and Intermessage Delays To obtain warranty or non-warranty service, return the unit to Hand Held Products postage paid with a copy of the dated purchase record attached. RS Handshaking RS handshaking is a set of rules concerning the exchange of data between serially communicating devices. Hand Held Products shall not be liable for technical or editorial errors or omissions contained herein; nor for incidental or consequential damages resulting from the furnishing, performance, or use of this material. This also sets the transmission rate to 36 scans per second and the polarity to white high.
HANDHELD BARCODE SCANNER IT3800 DRIVER
Hand Held Products IT3800 Scanner User Manual